where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

NDTSS - Non Destructive Testing Society of Singapore
Come & join the membership of NDTSS, Gain access to international developments.

320 views
Job Offers
J.Hill
Director, Field Operations
IMAC, USA, Joined Jun 2008, 4

J.Hill

Director, Field Operations
IMAC,
USA,
Joined Jun 2008
4
06:20 Jun-24-2008
NDT Level II or III

Posted by  
Job Location: MI-USA

THIS POSITION IS OPEN TO U.S. CITIZENS ONLY DUE TO THE CONTRACTORS ASSOCIATION WITH THE DEPARTMENT OF DEFENSE. IMAC has an opening for a temporary position: NDT Level II or III MT Specialist. The job is slated to start the first week of July, 2008. The position would require crossing a picket line during a labor dispute. The job details are as follows:
Position Summary: The NDT Level II or III Specialist reports to the Quality Leader and is responsible for the day-to-day technical support for all nondestructive testing. This individual will apply the NDT technologies of Magnetic Particle Inspection (MT). This individual will work in concert with the Quality Leader to provide the overall technical leadership for Nondestructive Evaluation at our client's facility.
· Will make final determination on acceptability of questionable hardware found by the NDT process, maintain all necessary documentation of the controls of the NDT processes, including their solutions and equipment.
· Will develop, update and institute NDT procedures and work instructions as required for existing equipment and implement new NDT inspection equipment, including necessary capability studies, procedures, work instructions and inspector training.
Position Requirements: The position requires a NDT level II or III MT certification.
Compensation: Hourly rate of $30.00 per hour level II or $35.00 per hour level III. Perdiem $35.00 a day. Housing and travel provided. Will be working 7 days a week 12 hours per day. Reply by email for consideration.


 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window