where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

DASEL SISTEMAS
Our Phased Array equipments, based on SITAU Technology, are among the PAS highest performance in the market.
570 views
Technical Discussions
Marvin Klein
Director, -
Intelligent Optical Systems, USA, Joined Nov 1998, 3

Marvin Klein

Director, -
Intelligent Optical Systems,
USA,
Joined Nov 1998
3
19:46 Jan-21-2009
High frequency transducer with calibrated surface displacement

In order to calibrate an optical interferometer, I am looking for a transducer or other source with a known surface displacement (or velocity) when driven at a single frequency. The frequency range of interest is 20-150 MHz and eventually to 1 GHz. Resonant transducers at fixed frequencies would be OK. A small thin film device would be fine, as we can focus to a ~100 um spot.

 
 Reply 
 
Elmar van den Elzen
Elmar van den Elzen
23:07 Jan-24-2009
Re: High frequency transducer with calibrated surface displacement
In Reply to Marvin Klein at 19:46 Jan-21-2009 (Opening).

Dear Marvin,

Precision Acoustics in the UK makes special hydrophones and ultrasound transducers for medical, NDT and scientific applications. They might be able to help you. Check out their web-site http://www.acoustics.co.uk/home.

Good luck, Elmar

 
 Reply 
 
Gerhard Splitt
R & D, -
Private, Germany, Joined Nov 1998, 38

Gerhard Splitt

R & D, -
Private,
Germany,
Joined Nov 1998
38
11:48 Jan-26-2009
Re: High frequency transducer with calibrated surface displacement
In Reply to Marvin Klein at 19:46 Jan-21-2009 (Opening).

Hi Marvin,

an alternative supplier could be Force Technology in Denmark, They are offering calibrated hydrophones; see http://www.force-institute.dk

Good luck,
Gerhard

 
 Reply 
 

Product Spotlight

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window