where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

KARL DEUTSCH
INSTRUMENTS AND SYSTEMS FOR NON-DESTRUCTIVE TESTING OF MATERIALS.
1909 views
Career Discussions
Abbas Bombaywala
NDT Inspector
Free Lance, India, Joined Jul 2007, 92

Abbas Bombaywala

NDT Inspector
Free Lance,
India,
Joined Jul 2007
92
14:55 May-25-2009
Corrosion Mapping Calibration Block & Standards

Dear Member,

I want to know that are there any special codes and standard for Corrosion mapping or we have to just use the Asme Sec V article 4 for Manual UT, Is there any standard calibration block for Corrosion mapping,

How about if we can make one of our own calibration blocks with FBH of 1 mm & 2 mm dia with the different depth simulating the different percentage loss. for example for 10 mm plate 1 mm & 2 mm dia FBH with different depths from 50 % to 90 % of the thickness. Can we make this type of calibration block and prove the sensitivity.

Quick & Prompt reply will be highly appreciated

    
 
 Reply 
 
Mark Nel
Sales, Application support
Technology Design Ltd., United Kingdom, Joined Jul 2005, 58

Mark Nel

Sales, Application support
Technology Design Ltd.,
United Kingdom,
Joined Jul 2005
58
01:57 May-28-2009
Re: Corrosion Mapping Calibration Block & Standards
In Reply to Abbas Bombaywala at 14:55 May-25-2009 (Opening).

Abbas, As corrosion mapping is an in service inspection and is usually requested as part of the wider corrosion control effort, it is to my knowledge rarely approached from a strict regime controlled by a specification but rather a procedure or technique is established based on the corrosion mapping equipment manufacturers particular method of applying this procedure in his hardware/software and configuring these to conform with the corrosiom department/engineers requirements. This department or individual quite often even looks to the service provider to supply the procedure for the task. There may even be several alternatives that you could choose from to best complete the task. Although, I guess there's nothing wrong with making a block with artificial defects to qualify the procedure, remember that all you really are doing is measuring thickness and translating these wall thickness readings into a colour-graphic image that provides an excellent means of identifying trends. The actual data may also be interrogated in minute detail using the available software tools (cursors etc.) to provide specific depth readings of each recorded area (pixel). I suggest that you contact the equipment vendor, as suggested by a previous respondent, to get a step-by-step guide on how to configure system for corrosion mapping.

    
 
 Reply 
 

Product Spotlight

FlexoFORM™

The FlexoFORM™ solution integrates flexible phased array probe technology in a scanner to solv
...
e the challenges that come with inspecting pipe elbows. When combined with a water column, this solution can be used to collect easy-to-interpret data on elbows with diameters ranging from 4.5 in. OD up to flat and offers many benefits.
>

Ultrasonic tomograph for imaging of concrete structures А1040 MIRA

Applicable for concrete inspection allowing imaging of the internal structure of objects from conc
...
rete, reinforced concrete, different stones. The operation applies pulse-echo technique at one-side access to the object. The instrument is feasible for concrete inspection for searching conduct ducts, conduits, detection of foreign inclusions, holes, honeycombing, cracks and other concrete defects.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window