where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Acoustic Emission Consulting, Inc.
Acoustic Emission Consulting, Inc. specializes in the design of small portable AE instruments for field and lab use.
438 views
Job Offers
ALI AZIS BIN SALLEH
ALI AZIS BIN SALLEH
18:55 Jun-06-2009
UT-CROSSCHECKER-SABAH SHELL(10 YEARS EXPERIENCED AND ABOVE ONLY)

Posted by Techno Analysis Sdn Bhd
Job Location: MMHE,Pasir Gudang,Johore.MALAYSIA

Job Title : FPS NDE Specialist
Team : Gumusut –Kakap Host Construction Team
Reports to : Gumusut – NDE Lead
Work Location : Johor Bahru
From : September 2008 To: March 2011

To perform UT Crosschecks of completed welds and weld repairs in addition to welds designated by the Engineer of Record.
Carry out NDT Surveillances in all methods to ensure that there is no non–compliances arising from technicians use of the approved procedures.
Assist in training with Contractors NDE Technicians to ensure compliance to Principals specifications and ensure that technicians improve their overall competency and ability.
Work with technicians on a one to one basis on-site to improve technicians overall competency and ability.
Monitor Contractor’s NDT equipment calibration practices and applied field examination techniques and validate contractor’s reported NDT results and NDE key performance indicators.

NDE Specialist Responsibilities:
• Familiarize self with Project NDE specifications, requirements and recommended practices (i.e. API and AWS).
• Provide input on NDE methods, procedures, processes and techniques.
• Provide feedback on approval of Contractor’s NDE personnel after witnessing field performance application and identify weaknesses through monitoring and crosschecking and carry out one to one training in order to improve level of competency of Contractors NDE techs.
• Monitor the set up, application and results of Non-Destructive testing by Contractor.
• Monitor calibration of equipment, and review certification data of personnel and equipment.
• Perform routine checks to ensure NDE techniques and methods are uniform and consistent throughout all aspects in testing and verification of welded works.
• Carry out UT cross checking, RT film review, NDE Surveillances and review of NDE records produced by the Contractor.
• Assist in the location of percentage and random NDE examinations on a daily basis in the field.
• Monitor Contractor recording of NDE examinations performed and test results; including weld repairs.
• Provide input on Contractor’s Weld Maps and NDE Identification scheme field application and traceability effectiveness.
• Prepare list of outstanding NDE for inclusion in final punch list.

Qualification & Experience

• Ultrasonic Inspection – shall be qualified to a minimum of Level II by a Certification body such as PCN or by an Employers Written Practice in accordance with SNT-TC-1A (or equivalent).

• Radiographic Interpretation – shall be qualified to a minimum of Level II by a Certification body such as PCN or by an Employers Written Practice in accordance with SNT-TC-1A (or equivalent).

• A Level II qualification in or at least a sound knowledge of MPI/PT.

• Experience – should have a minimum of ten years experience in NDE associated with Offshore Oil and Gas projects.

• Be able to specialize in the detailed examination of weldments (TKY, Cruciform, T-joints, Y-joints and single and double-sided joints etc), development of relevant Procedures and Techniques, including but not limited Magnetic Particle Inspection, Liquid Penetrant Inspection, Radiographic Interpretation and Ultrasonic Inspection.

• Be familiar with defect types associated with different welding methods.

• Recognize the problems that are associated with welding in areas of high restraint (repairs) and the defects that are typical in these locations.

• Have past experience in offshore construction yards, preferably as a Clients Crosschecker.

• Past experience working on TLP/FPS or similar Semi Submersible vessels.

• A knowledge of the following codes and publications as a minimum; AWS D1.1 Structural Code, API-RP2X Recommended Practices for UT and MT and also SNTC-TC-1A and PCN qualification requirements.

• Familiar with Welding and Inspection practices, Fabrication Specifications and Fabrication sequences in order to identify any potential NDE problems that may arise from the methods applied during production.

• NDE experience working with various materials including welding to castings and the various techniques and associated defects.

• Be fluent in English language and must be a good communicator as the job entails interacting with contractor NDE personnel.

• Strong documentation skills required.

• Competent in the review of NDE Reports and records.

• Competent computer skills in Microsoft Office products including Word and Excel

 
 

Product Spotlight

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window