where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
585 views
Technical Discussions
fanta diop ndiaye
Engineering, Industry Manager
BUREAU VERITAS DAKAR, Senegal, Joined Feb 2006, 3

fanta diop ndiaye

Engineering, Industry Manager
BUREAU VERITAS DAKAR,
Senegal,
Joined Feb 2006
3
13:27 Aug-26-2009
inspection of welding

we find allways after LPI examination of the welding some cracks in de base material.
we want to know what's happend? If somebody can help.

the base material is steel S 235 jr, the electrodes are E7018, the welding process 111

Any information is appreciated.

    
 
 Reply 
 
Michał
NDT Inspector, Welding Inspector, Mechanical Inspector on behalf of TPI companies
MIDYTEST, Poland, Joined Aug 2007, 14

Michał

NDT Inspector, Welding Inspector, Mechanical Inspector on behalf of TPI companies
MIDYTEST,
Poland,
Joined Aug 2007
14
21:51 Aug-26-2009
Re: inspection of welding
In Reply to fanta diop ndiaye at 13:27 Aug-26-2009 (Opening).

Probably cracks you have mentioned are hydrogen cracks.
Is it possible that you haven't died electrodes enough?
Remember that you absolutly have to dry alkalic electrodes for 1-2 hours in 300-350 C degree.
But I might be wrong - please give some more details if you can.
Best regards
Mike

    
 
 Reply 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window