where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1092 views
Technical Discussions
junho
NDT Inspector,
KOREA Material INSPECTION, South Korea, Joined Oct 2009, 21

junho

NDT Inspector,
KOREA Material INSPECTION,
South Korea,
Joined Oct 2009
21
14:22 Feb-19-2010
creeping wave methode

hi all

I wondering, Is ASME explaining creeping wave method
for ID deadzone inspect

thank you

 
 Reply 
 
Carlos Correia
R & D, - -
UCV & EGROUP, Venezuela, Joined Oct 2008, 120

Carlos Correia

R & D, - -
UCV & EGROUP,
Venezuela,
Joined Oct 2008
120
19:05 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Hello Junho, CW Method is still beyond ASME considerations. You should to check the 2007 edition. But you can write to Ed Ginzel or to Mark Davis. They are part of this forum and is sure they know...

 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1286

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1286
19:09 Feb-19-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Mr Park
ASME does not describe the "so-called" creeping wave. When you examine the arrival times of the signals when peaking a small depth notch on the opposite wall it will be seen that the detection is actually achieved by the shear headwave. This can be done using a refracted compression mode at some angle between about 70° to 80°
Good description can be found on the application of the techniques in general on http://www.ndt.net/article/pow1297/schmid/schmid.htm

 
 Reply 
 
andrew cunningham
NDT Inspector
Canada, Joined Jun 2008, 238

andrew cunningham

NDT Inspector
Canada,
Joined Jun 2008
238
23:55 Feb-22-2010
Re: creeping wave methode
In Reply to junho at 14:22 Feb-19-2010 (Opening).

Download Mode Change, Creeping Wave or Corner Trap???

Hi Junho

Please find attachment that may explain acoustics of an ID connected reflector.
I hope it helps you.

Yours sincerely
Andrew
 
 Reply 
 

Product Spotlight

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

NEOS III

NEOS III is Logos Imagings lightest DR system. With a built-in battery and internal wireless commu
...
nication, the NEOS III is perfect for users that want to quickly assess an item.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window