where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ACS-Solutions GmbH
develop and manufacture hi-tech devices for Ultrasonic Testing

192 views
Technical Discussions
Omid Ghorbanian
Omid Ghorbanian
05:07 Sep-26-2001
Control of welding parameters with eddy current


: Dear colleagues,

We have a welder(MIG/MAG/TIG) robot(in Amirkabir university of thechnology-IRAN-TEHRAN) and we would like to control it with eddy current response.
Therfore we would like to make an overview of manner "automatic welding with on-line inspection
of eddy current" so that The operating welding variables affect the working of the process,
and can be adjusted during the welding operation i.e.: intensity I, voltage U, welding speed V
,distance between electrode and workpice etc. etc. are adjasted automaticaly (as for the
eddy current response)for production weld with the best quality. (welding parameters are chosen
to match the strength and toughness mechanical properties)

What are the main factors involved and roughly how much variations can these factors
be expected to cause?

: : what is the influence of welding parameters (such as intensity I, voltage U,
welding speed V,distance between electrode and workpice etc. etc.) with eddy current signal?

: : what is the influence of weld quality (shch as toughness and strength etc.) with
eddy current signal?

: : Does you have experience with such factors?

: : Does you know existing literature or website with a proper covering of this subject?

: : We are especially looking forward to replies relevant to control of automatic welding parameters with eddy current in ferromagnetic steel type.


: :Omid Ghorbanian


    
 
 

Product Spotlight

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window