where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

289 views
Technical Discussions
Xavier
Xavier
05:22 Jun-07-2002
European Post-doc and visiting scientist positions

FOR MORE INFORMATION, CONTACT DIRECTLY Dr A. Eriksson by e-mail eriksson@jrc.nl

Post Doc Fellowships and visiting scientist fellowships at ENIQ / Inspection Management Sector

The Inspection Management Sector of the Institute of Energy is the operating agent of ENIQ –the European Network for Inspection and Qualification. The sector performs research, usually in multi-partner projects in order to i) assess and qualify non destructive evaluation inspection techniques and procedures primarily for nuclear components, ii) harmonise codes and standards at European level in the field of Inspection Qualification and Risk-informed In-service Inspection and to iii) set up a co-ordinated EU approach for qualification of in-service inspection. ENIQ covers pilot studies simulating in-service inspections, qualification of in-service inspections, drawing up of recommended practices for inspection qualification, verifying the feasibility to implement a European system of recognition at European level of inspection qualification exercises and studying risk informed concepts and their influence on inspection qualification. We are now announcing the following fellowships:

1. Post-doc Fellowship for a scientist with experience in risk informed decision-making techniques for inspection and/or maintenance planning. Knowledge in probabilistic risk analysis is desirable. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

2. Post-doc Fellowship for a specialist in ultrasonics, experimental and/or modelling. Possible areas to be covered are: applications of ultrasonic Phased Array system to in-service inspection (ISI) problems; inspection problems/modelling of austenitic welds (scattering, attenuation, beam skewing etc), modelling and simulation of ultrasonic ISI. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

3. Post-doc Fellowship for an inspection qualification specialist with knowledge in the use of technical justification in the qualification process, modelling, reliability studies of the different components in the In-service Inspection system (procedures, equipment and personnel). Experience with ultrasonics is desirable, but other techniques are also welcome. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

4. Visiting scientists (all nationalities, less than 65 years old, with good track record in NDT R&D on the topics described in points 1, 2 and 3). More information on request.

Minimum requirements :
- to be less than 35 years old (Visiting scientists: less than 65 years old)
- to be a European citizen (or a member of an associated states) – Visiting scientists (any nationalities)
- to have a PhD degree

Contract duration: 2 ~ 3 years.
Location: The Netherlands, Europe.

FOR MORE INFORMATION, CONTACT DIRECTLY Dr A. Eriksson by e-mail:
eriksson@jrc.nl



 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window