The Largest Open Access Portal of Nondestructive Testing (NDT)

934 views Technical Discussions Dana Ives Engineering CoreStar International Corp., USA, Joined Jan 2003, 10 Dana Ives Engineering CoreStar International Corp., USA, Joined Jan 2003 10 05:51 Jan-09-2004 Corten Tubing I am trying to get information concerning Corten tubing material. Its UNS number is K11535 with an ASTM of A423A & 423M. We are trying to locate some of this material to fabricate a standard that would be used to inspect the tubes of a Moisture Separator Reheater (MSR). If anyone out there can shed light, it would be most appreciated.                  Reply  Translate  Close   N.Kuppusamy Consultant, NDT Level-III Engineer Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003, 34 N.Kuppusamy Consultant, NDT Level-III Engineer Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003 34 02:15 Jan-11-2004 Re: Corten Tubing Dana Ives, The composition of ASTM A423 as follows: Gr.1 Gr.2 C 0.15 0.15 Mn 0.55 0.50-1.00 S 0.06 0.05 Si 0.10 ---- Cu 0.20-060 0.30-1.00 Cr 0.24-1.31 ---- Ni 0.20-0.70 0.40 -1.10 Mo ---- 0.10 Note: all single values indicates maximum percentage. For more details regarding suppliers, please visit the site: http://www.metalinfo.com/ Regrads, N.Kuppusamy ----------- Start Original Message ----------- : I am trying to get information concerning Corten tubing material. Its UNS number is K11535 with an ASTM of A423A & 423M. We are trying to locate some of this material to fabricate a standard that would be used to inspect the tubes of a Moisture Separator Reheater (MSR). If anyone out there can shed light, it would be most appreciated. ------------ End Original Message ------------                  Reply  Translate  Close   Keith Woods Keith Woods 05:49 Feb-26-2004 Re: Corten Tubing ASTM A847 is the proper specification for Corten equivalent tubing ----------- Start Original Message ----------- : Dana Ives, : The composition of ASTM A423 as follows: : Gr.1 Gr.2 : C 0.15 0.15 : Mn 0.55 0.50-1.00 : S 0.06 0.05 : Si 0.10 ---- : Cu 0.20-060 0.30-1.00 : Cr 0.24-1.31 ---- : Ni 0.20-0.70 0.40 -1.10 : Mo ---- 0.10 : Note: all single values indicates maximum percentage. : For more details regarding suppliers, please visit the site: : http://www.metalinfo.com/ : Regrads, : N.Kuppusamy : : I am trying to get information concerning Corten tubing material. Its UNS number is K11535 with an ASTM of A423A & 423M. We are trying to locate some of this material to fabricate a standard that would be used to inspect the tubes of a Moisture Separator Reheater (MSR). Ifanyone out there can shed light, it would be most appreciated. ------------ End Original Message ------------                  Reply  Translate  Close   friend-finder friend-finder 02:07 May-05-2004 Re: Corten Tubing ----------- Start Original Message ----------- : Dana Ives, : The composition of ASTM A423 as follows: : Gr.1 Gr.2 : C 0.15 0.15 : Mn 0.55 0.50-1.00 : S 0.06 0.05 : Si 0.10 ---- : Cu 0.20-060 0.30-1.00 : Cr 0.24-1.31 ---- : Ni 0.20-0.70 0.40 -1.10 : Mo ---- 0.10 : Note: all single values indicates maximum percentage. : For more details regarding suppliers, please visit the site: : http://www.metalinfo.com/ : Regrads, : N.Kuppusamy ------------ End Original Message ------------ I am trying to get information concerning Corten tubing material. Its UNS number is K11535 with an ASTM of A423A & 423M. We are trying to locate some of this material to fabricate a standard that would be used to inspect the tubes of a Moisture Separator Reheater (MSR). If anyone out there can shed light, it would be most appreciated. Adult Friend Finder                  Reply  Translate  Close   Product Spotlight iProbe - USB Phased Array Probe StandHi-Spec Systems Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas ... ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality. > 3 Showcases3 Videos High Resolution Industrial CT System for Small/Medium Size Parts Inspection - YXLON FF35 CT StandYXLON International GmbH The YXLON FF35 CT computed tomography system is designed to achieve extremely precise inspection r ... esults for a wide range of applications. Available in a single or dual tube configuration, it is perfect for very small to medium size parts inspection in the automotive, electronics, aviation, and material science industries. > 5 Showcases GUL QSR1® Scanning StandGuided Ultrasonics Ltd. How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav ... e Quantitative Short Range Scanning. > 21 Showcases4 Videos NEW - TD Focus-ScanRX StandTechnology Design Ltd The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut ... ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input > 4 Showcases4 Videos more Showcases Share... Home Exhibition Archive Forum Jobs Members Events Directory NDT A-Z Advertise Privacy Policy Contact About © NDT.net - Where expertise comes together. The Largest Open Access Portal of Nondestructive Testing (NDT)- since 1996 We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info Accept top this is debug window