where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

I&T Nardoni Institute
A state-of-the-art company servicing the metal, mechanical, aeronautical and railway industrial sectors

1066 views
Technical Discussions
Jim McGregor
Jim McGregor
01:23 Jun-02-2004
Attenuation measurments to check for hydrogen attack

I am looking for information on carrying out attenuation measurments on a 75mm thick carbon steel vessel before and after heat soak to check for hydrogen dispersement. The vessel has been in use for the past 10 years or so. Any help with details and /or a test procedure would be appreciated.

Thanks,

Jim McGregor


    
 
 
Sasaki
Sasaki
03:34 Jun-02-2004
Re: Attenuation measurments to check for hydrogen attack
There are five methods to detect a certain type of hydrogen attack:
1) flaw echo
2) attenuation
3) frequency analysis
4) sound velocity
5) comparison of longitudinal/transverse sound velocities


    
 
 
Kasper Pols
Kasper Pols
09:35 Jun-02-2004
Re: Attenuation measurments to check for hydrogen attack
----------- Start Original Message -----------
: I am looking for information on carrying out attenuation measurments on a 75mm thick carbon steel vessel before and after heat soak to check for hydrogen dispersement. The vessel has been in use for the past 10 years or so. Any help with details and /or a test procedure would be appreciated.
: Thanks,
: Jim McGregor
------------ End Original Message ------------

See website: Sensistor



    
 
 
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
04:28 Jun-02-2004
Re: Attenuation measurments to check for hydrogen attack
----------- Start Original Message -----------
: : I am looking for information on carrying out attenuation measurments on a 75mm thick carbon steel vessel before and after heat soak to check for hydrogen dispersement. The vessel has been in use for the past 10 years or so. Any help with details and /or a test procedure would be appreciated.
: : Thanks,
: : Jim McGregor
: See website: Sensistor
------------ End Original Message ------------
Jim,

Detection and monitoring is not a simple subject.
First of all you have to define what type of Hydrogen damage can be expected. Is the vessel operating in high temperature / high pressure environment? In this case you could have High Temperature Hydrogen Attack. Is it working at low temperature, you might be looking at one or more types of Hydrogen Induced Cracking. There is not one method that on its own will give you a conclusive answer on whether you do or don't have Hydrogen Damage. Therefore, during the last 15 years we have developed and practiced combinations of techniques, optimised for the situation at hand. We provide the service worldwide, so if you are interested let us look at your challenge.

Best regards,

Jan Verkooijen



    
 
 

Product Spotlight

Alpha Pro Digital Radiography System

The Alpha Pro digital X-ray system is the ideal system for your NDT \r\nneeds, as it offers amazin
...
g 16 bit images which enable the highest \r\nlevel of detection and identification of hairline cracks. While weighing only 3kg (6.6lbs), this panel has the largest imaging area: 35 X 43 cm (14X17 in).
>

TVC awarded UKAS accreditation

TVC are delighted to finally announce we have been awarded UKAS accreditation for our calibration
...
laboratory. Laboratory accreditation to ISO/IEC 17025:2005 enables us to conduct the Electrical Verification of Ultrasonic Flaw Detection Equipment to BS EN 12668-1:2010. It has taken many months of hard work and we want to thank our staff for all their efforts during this massive undertaking.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window