where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

TecScan Systems
We offer a complete line of NDT scanners, Immersion Tanks & Gantry systems which incorporate Ultrasonic, Phased Array & Eddy Current technologies.

257 views
Technical Discussions
R. Gopal
R. Gopal
08:42 Mar-07-2005
Re: Bimetallic Tube Inspection

with real authenticity for the above achievemnt of results shall contact me also.

Thanks & regards

R. Gopal


:
Dear All,
.
: We have a HP. Stripper in Urea Plant licensed by Snaphrogetti which have tubes made from bimetallic material ( Stainless steel + Zr ). Any of you could inform me the best method to be used to inspect the internal of that tube ? Thank you.
.


--
This message was posted into the NDT.net Forum.
http://www.ndt.net/wshop/forum/forum-1.htm
Please do not reply to email: forum@ndt.net
For your reply to this message go to:
http://www.ndt.net/wshop/forum/messages-1/8044.html


    
 
 
Simon Amallraja
Simon Amallraja
06:13 Mar-08-2005
Re: Bimetallic Tube Inspection
lay 25-22-2 surface corrosion due to "Active" attack to be assessed.
: NDT personnel with real authenticity for the above achievemnt of results shall contact me also.
: Thanks & regards
: R. Gopal
:
: :
: Dear All,
: .
: : We have a HP. Stripper in Urea Plant licensed by Snaphrogetti which have tubes made from bimetallic material ( Stainless steel + Zr ). Any of you could inform me the best method to be used to inspect the internal of that tube ? Thank you.
: .
:
: --
: This message was posted into the NDT.net Forum.
: http://www.ndt.net/wshop/forum/forum-1.htm
: Please do not reply to email: forum@ndt.net
: For your reply to this message go to:
: http://www.ndt.net/wshop/forum/messages-1/8044.html
------------ End Original Message ------------

Dear Mr.Gopal,

We represent Zetec Inc, USA for their entire product ranges in India. They are the World Leaders in Eddy Current Instrumnets and Systems. If you can give your contact no and address, we willgetin touch with you and help you to solve the problem, with the help of our Principals ZETEC, USA.

Simon Amallraja.
Mobile: 098663 43309. Contact me for further info.


    
 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Alpha Pro Digital Radiography System

The Alpha Pro digital X-ray system is the ideal system for your NDT \r\nneeds, as it offers amazin
...
g 16 bit images which enable the highest \r\nlevel of detection and identification of hairline cracks. While weighing only 3kg (6.6lbs), this panel has the largest imaging area: 35 X 43 cm (14X17 in).
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window