where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Sonotron NDT
Original developer and manufacturer of advanced ultrasonic instruments
710 views
Technical Discussions
Fred Raco, Jr.
Consultant,
RNDT, Inc., USA, Joined Jul 2002, 24

Fred Raco, Jr.

Consultant,
RNDT, Inc.,
USA,
Joined Jul 2002
24
05:06 Apr-22-2005
super austenitic plate material

Can anyone assist us on a way of measuring the residual magnetism (if any) on a super austenitic plate material after welding?


    
 
 Reply 
 
DJ Kallhof
DJ Kallhof
01:26 Apr-22-2005
Re: super austenitic plate material
Austenitic stainless steels unlike Martensitic don't typically have residual magnetism problems. To verify this I would suggest using a Hall Effect Probe. Just out of curiousity, what is the AMS number of the material you are dealing with?
----------- Start Original Message -----------
: Can anyone assist us on a way of measuring the residual magnetism (if any) on a super austenitic plate material after welding?
------------ End Original Message ------------




    
 
 Reply 
 
Jim Knowles
Jim Knowles
02:54 Apr-28-2005
Re: super austenitic plate material
Austenitics do suffer from a magnetic effect especially after a weld repair, its called retained Delta ferrite.
Too higher delta ferrite can impair the corrosion properties of the stainless material. The delta ferrite levels usually found after welding to an approved weld procedure can be between 3-6% Fe, on repairs to a repair or un authorised re running of weld cap profiles levels of Fe can rise to around 10-12%.
Equipmemt used to measure accurately is the Forster Mangnetoscop 1.068 model.


----- Start Original Message -----------
: Austenitic stainless steels unlike Martensitic don't typically have residual magnetism problems. To verify this I would suggest using a Hall Effect Probe. Just out of curiousity, what is the AMS number of the material you are dealing with?
: : Can anyone assist us on a way of measuring the residual magnetism (if any) on a super austenitic plate material after welding?
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

Silverwing RMS PA - Phased-array corrosion mapping

Eddyfi Technologies integrated two market leading solutions, Silverwing’s RMS and M2M’s instru
...
ments to provide a high-speed, remote access ultrasonic phased-array inspection system with live total focusing method (TFM).
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

FlexoFORM™

The FlexoFORM™ solution integrates flexible phased array probe technology in a scanner to solv
...
e the challenges that come with inspecting pipe elbows. When combined with a water column, this solution can be used to collect easy-to-interpret data on elbows with diameters ranging from 4.5 in. OD up to flat and offers many benefits.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window