where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1537 views
Technical Discussions
Michael Crapps
Michael Crapps
01:58 May-19-1999
UT Thickness Verification Old Piping - Equipment Needs

Looking for an inexpensive gage, don't need all the bells
and whistles, just good performance at a reasonable cost.
Will need to verify remaining wall thickness of piping
that has been in service for a number of years - have no way
to know the as-is condition until we go into a shutdown.


Also want to use this gage for material thickness verifications
of newer fabrications - in good condition.


Any leads would be appreciated.




 
 Reply 
 
Wieslaw Bicz
Engineering,
PBP Optel sp. z o.o., Poland, Joined Feb 2009, 276

Wieslaw Bicz

Engineering,
PBP Optel sp. z o.o.,
Poland,
Joined Feb 2009
276
02:06 May-19-1999
Re: UT Thickness Verification Old Piping - Equipment Needs

: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

:
: Also want to use this gage for material thickness verifications
: of newer fabrications - in good condition.

:
: Any leads would be appreciated.

I think, we can offer you such gage, Please see info on our page (http://www.optel.com.pl/manual/english/osc2.htm).

Soon we will have a portable device (but it must be connected to a
computer - notebook for example).

Wieslaw Bicz



 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
02:24 May-19-1999
Re: UT Thickness Verification Old Piping - Equipment Needs

: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

:
: Also want to use this gage for material thickness verifications
: of newer fabrications - in good condition.

:
: Any leads would be appreciated.

Panametrics is one of the several worldwide companies that offer hand-held ultrasonic gages for measurement of remaining wall thickness. The Model 26MG is our simplest (and least expensive) standard model. You can find details on our web site at

http://www.panametrics.com/ndt/thickness/

--Tom Nelligan


 
 Reply 
 
Peter Simpson
Director,
Ashtead Technology Ltd, United Kingdom, Joined Oct 1999, 12

Peter Simpson

Director,
Ashtead Technology Ltd,
United Kingdom,
Joined Oct 1999
12
09:51 May-20-1999
Re: UT Thickness Verification Old Piping - Equipment Needs
: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

:
: Also want to use this gage for material thickness verifications
: of newer fabrications - in good condition.

:
: Any leads would be appreciated.


Why don’t you rent a thickness meter (see www.ashtead-technology.com)as in this way you benefit.


 No compromise on performance against initial cost.
 No ongoing Calibration or Maintenance Costs.
 No large capital outlay.
 Simply return and upgrade whenever you require a differently specified model or if you want to evaluate different models.
 No Depreciation costs.
 Wide range of models available.

Systems are available at competitive rates for short or long term rental. All equipment supplied ready for use.




 
 Reply 
 
Dave Cartwright
Dave Cartwright
09:57 May-20-1999
Re: UT Thickness Verification Old Piping - Equipment Needs
: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

:
: Also want to use this gage for material thickness verifications
: of newer fabrications - in good condition.

:
: Any leads would be appreciated.

Michael, give me a call anytime 09:00 to 17:30 UK time to discuss your requirements. We offer a range of sensibly priced equipment that will meet your needs and you do not need to worry about operator experience or training.

+44(0)1305-265533


 
 Reply 
 
Jan Verkooijen
Director,
Sonovation, Netherlands, Joined Nov 1998, 29

Jan Verkooijen

Director,
Sonovation,
Netherlands,
Joined Nov 1998
29
06:31 May-21-1999
Re: UT Thickness Verification Old Piping - Equipment Needs
: : Looking for an inexpensive gage, don't need all the bells
: : and whistles, just good performance at a reasonable cost.
: : Will need to verify remaining wall thickness of piping
: : that has been in service for a number of years - have no way
: : to know the as-is condition until we go into a shutdown.

: :
: : Also want to use this gage for material thickness verifications
: : of newer fabrications - in good condition.

: :
: : Any leads would be appreciated.

: Michael, give me a call anytime 09:00 to 17:30 UK time to discuss your requirements. We offer a range of sensibly priced equipment that will meet your needs and you do not need to worry about operator experience or training.

: +44(0)1305-265533

I would just like to express a word of caution here.
Obviously it depends upon the type of piping you need to
inspect: a simple waste water line might not need
the same stringent inspection as a high pressure hydrogen
line. Also, I could imagine an operator with little training
doing incoming goods checks with a simple thickness gauge,
but on used piping, where you do not know what to expect
I would recommend to use fully trained and qualified personnel
to be used for the inspection. A cheap solution might turn out
very expensive if you think of the possible risk involved.
Another side to it is that it might be a good idea to look
at the welds as well as the piping itself. Many times it has
happened before that root corrosion/erosion of welds in piping
was the cause of extended shutdowns cause by replacement and
repair of piping being needed.
I would recommend, obviously dependant upon your actual
needs(type of piping, application etc.) to get some advise from a qualified and certified
NDE company. It might cost you a little money now, but it
could save you a lot. Obviously if you wis to discuss this
in a bit more detail, I would gladly speak to you (free of charge!)
on +31 162 42 55 88.

Jan Verkooijen
AEASonomatic


 
 Reply 
 
Jim Johnson KM943
Jim Johnson KM943
07:00 May-29-1999
Re: UT Thickness Verification Old Piping - Equipment Needs
: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

I agree with Jan Verkooijen, you have not presented enough data to make
any determination. A simple thickness gage can lead to misinterpretations.
For determinations of hoop stress you need length, width and depth. What kind of sampling
are you proposing? What materials are being transported? With a simple hand held instrument
using a good sampling technique, what are the odds of finding a critical flaw on your surface area?
You may want to go to an instrumented pig for 100% coverage or computer controled
external scanning (if the surface is good).

I have about 15 years in piping and e/c and there is not a simple answer, nor, typically, a
single piece of equipment which will resolve your problem. I have had pipe rupture between sampling
points (egg in the face). You need to resolve your risk tolerance, not just the inspection equipment issue.

JJ NDT III KM 943
:
: Any leads would be appreciated.




 
 Reply 
 
prabhat
prabhat
00:09 Jan-16-2001
Re: UT Thickness Verification Old Piping - Equipment Needs
: Looking for an inexpensive gage, don't need all the bells
: and whistles, just good performance at a reasonable cost.
: Will need to verify remaining wall thickness of piping
: that has been in service for a number of years - have no way
: to know the as-is condition until we go into a shutdown.

:
: Also want to use this gage for material thickness verifications
: of newer fabrications - in good condition.

:
: Any leads would be appreciated.





 
 Reply 
 

Product Spotlight

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window