where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

574 views
Technical Discussions
dharmaraj
dharmaraj
03:52 Jul-06-2005
film viewers.

Hai friends,
How to calibrate the film viewer.


 
 Reply 
 
Ed T.
Ed T.
06:11 Jul-09-2005
Re: film viewers.
----------- Start Original Message -----------
: Hai friends,
: How to calibrate the film viewer.
------------ End Original Message ------------

Try using a density strip.


 
 Reply 
 
N.Arunachalam
N.Arunachalam
07:40 Jul-29-2005
Re: film viewers.
----------- Start Original Message -----------
: : Hai friends,
: : How to calibrate the film viewer.
: Try using a density strip.
------------ End Original Message ------------

We have to use the light meter to measure the quantity of light from the viewer, if the viewer is meant for measuring film density of 4 , find the incident light requirement using the Code requiremnt at the surface of the viewer,

Assume 30 lux of transmited light on 4 density film is required for better viewing by normal eye condition then using the log priciple ,30 X 10,000 lux of incident light is required on the surface of viewer, but you cannot measure this high quantity light by normal low range light meters( in the market available meters having maximum 3000 lux only), so measure the light intensity in a pre determine vertical ( 750mm) distance from the viewer middle surface and calculate the amount of light intensity on the viewer by using inverse square law priciple.the calculated light must be more than 300,000 lux on the surface,( this value may vary if you asume differnt value of transmitted light indensity)



 
 Reply 
 

Product Spotlight

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window