where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

VOGT Ultrasonics GmbH
non-destructive testing, services, training, ultrasonic systems, immersion and squirter inspection systems, PROline, digital radiology
515 views
Technical Discussions
Zeki Cosku Gokce
Zeki Cosku Gokce
04:48 Oct-31-2005
Ultrasonic inspection of as-cast products

What is the best wavemode, frequency, sensor diameter to look for longitudinal cracks and shroud porosity on as-cast products such as slabs and billets from a steel mill? we are trying to inspect a 150mm square billet but cannot see the backwall reflection (there seems to be a lot of scattering). Any ideas?


 
 Reply 
 
A.A.AMIRI
Consultant, NDT/QC/WELD INSPECTION
Iran, Joined Nov 2005, 20

A.A.AMIRI

Consultant, NDT/QC/WELD INSPECTION
Iran,
Joined Nov 2005
20
05:38 Nov-01-2005
Re: Ultrasonic inspection of as-cast products
----------- Start Original Message -----------
DEAR FRIEND,
I THINK FOR YOUR TEST CONDITION,NORMAL PROBE WITH OVER 24mm.Dia.(LONGITUDINAL WAVE),0.25-1 MHZ FREQUENCY IS
WELL.YOU CAN ON-REGECT SWITCH FOR OMITTED OR DECREASE NOISE ON DISPLAY(CRT/LCD).HIGH DAMP PROBE MAY HELP YOU
FOR PREVENT OF NOISE EFFECTS.


 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window