where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

982 views
Technical Discussions
Mathias
Mathias
01:32 Nov-09-2005
EN Standard for wire IQI

Hi
Does anyone know which EN Standard covers/describes the wire iqi´s?


 
 Reply 
 
Uli Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Uli Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
09:32 Nov-11-2005
Re: EN Standard for wire IQI
----------- Start Original Message -----------
: Hi
: Does anyone know which EN Standard covers/describes the wire iqi´s?
------------ End Original Message ------------

Try EN 462-1 for the description of the wire IQI's and/or EN 1435 (welds) resp. EN 12681 (castings) for the wire IQ requirements.

Regards
Uli Mletzko
MPA, University of Stuttgart
(Germany)




 
 Reply 
 
Kaveh
Kaveh
07:26 Nov-14-2005
Re: EN Standard for wire IQI
----------- Start Original Message -----------
: : Hi
: : Does anyone know which EN Standard covers/describes the wire iqi?s?
: Try EN 462-1 for the description of the wire IQI's and/or EN 1435 (welds) resp. EN 12681 (castings) for the wire IQ requirements.
: Regards
: Uli Mletzko
: MPA, University of Stuttgart
: (Germany)
------------ End Original Message ------------

Dear Uli
Detail of IQI construction in EN-462-5-1996.
EN 462-1-1994 shows typical construction details of one design.
Tables of acceptable wire diameters for different specimen thickness are given in EN 462-3, EN 462-4 and EN 1435-1997.
This type of IQI is shown in detail in EN 462-2-1994
Tables of IQI sensitivities for the IQI on the film side are included in EN 1453-1997 and EN 462-3-1997.

Regards
Kaveh Edalati


 
 Reply 
 

Product Spotlight

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window