The Largest Open Access Portal of Nondestructive Testing (NDT)

362 views Technical Discussions Zeki Cosku Gokce Zeki Cosku Gokce 06:08 Dec-16-2005 Life prediction Fitness for Service software I am looking for boiler tube life prediction software. Anyone has any suggestions?                  Reply  Translate  Close   Doug Breeze Director, Consultant; R&D Inspection Software Limited, United Kingdom, Joined May 2000, 20 Doug Breeze Director, Consultant; R&D Inspection Software Limited, United Kingdom, Joined May 2000 20 01:13 Dec-17-2005 Re: Life prediction Fitness for Service software Boiler Tube Life Prediction Software The Power Technology Centre at E.ON UK (formerly PowerGen UK plc), market their 'PowerTube' suite specifically for boiler tube failure management. The suite includes two modules for life prediction. Follow the link below for details. Doug Breeze Inspection Software Ltd ----------- Start Original Message ----------- : I am looking for boiler tube life prediction software. Anyone has any suggestions? ------------ End Original Message ------------ PowerTechnology Centre (PowerTube suite)                  Reply  Translate  Close   Product Spotlight SONOAIR - air-coupled Phased Array Ultrasonic Inspection System StandSONOTEC Ultraschallsensorik Halle GmbH For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors, ... the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers. > 5 Showcases5 Videos ISAFE3 Intrinsically Safe Sensor System StandVallen-Systeme GmbH ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica ... l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A. > 2 Showcases GUL QSR1® Scanning StandGuided Ultrasonics Ltd. How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav ... e Quantitative Short Range Scanning. > 21 Showcases4 Videos High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2 StandSIUI (Shantou Institute of Ultrasonic Instruments Co.,Ltd) SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and ... 2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection. > 8 Showcases4 Videos more Showcases Share... Home Exhibition Archive Forum Jobs Members Events Directory NDT A-Z Advertise Privacy Policy Contact About © NDT.net - Where expertise comes together. The Largest Open Access Portal of Nondestructive Testing (NDT)- since 1996 We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info Accept top this is debug window