where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Materials Research Institute
Consulting to the NDT industry.

781 views
Technical Discussions
prakash
prakash
04:59 Jan-21-2006
NDT of fastner head

can the head of a fastner be tested for crack after forging using some NDT method? If so how?


    
 
 
P V SASTRY
P V SASTRY
00:15 Jan-22-2006
Re: NDT of fastner head
----------- Start Original Message -----------
: can the head of a fastner be tested for crack after forging using some NDT method? If so how?
------------ End Original Message ------------
They can be very easily tested for the presence of cracks/bursts using wet fluorescent magnetic particle testing(WFMPT),assuming that the fasteners are of ferromagnetic material. This is a fast and reliable method that will detect cracks of even a few microns width when properly applied. Alternately Dye Penetrant testing(PT) also can be used as a stop gap arrangement before you can procure the preffered WFMPT set up.In case the fastners are of non ferromagnetic materials like SS, PT (colour/fluorescent)can only be aplied.



    
 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
06:05 Jan-23-2006
Re: NDT of fastner head
----------- Start Original Message -----------
: can the head of a fastner be tested for crack after forging using some NDT method? If so how?
------------ End Original Message ------------

Dear Prakash,

Yes, there are several options. Magnetic Particle Testing is one (I am assuming that the fastener is magnetic). If you need real time high speed testing, you should think of automated UT and or RT. If you can accept batch testing mode, MT and PT (if non-magnetic material is invoved) may be good enough.

Swamy

Swamy



    
 
 

Product Spotlight

XRHRobotStar

In high volume industries like automotive the requirement for a hundred percent X-ray inspection c
...
reates a bottleneck in the production. The XRHRobotStar is a fully Automated Defect Recognition (ADR) capable robot-system that allows an ultra-fast in-line inspection.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window