where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

756 views
Technical Discussions
Charlie Jackson
Charlie Jackson
02:09 Mar-20-2006
UT Flaw detection in Monel and Hastelloy weldments

Interested to know of any UT Techniques for Monel or Hastelloy weldments which would give a reasonable POD for preferential ID corrosion loss to Weld or HAZ in piping.

Kind Regards Charlie


 
 Reply 
 
Frank
Frank
05:35 Mar-25-2006
Re: UT Flaw detection in Monel and Hastelloy weldments
----------- Start Original Message -----------
: Interested to know of any UT Techniques for Monel or Hastelloy weldments which would give a reasonable POD for preferential ID corrosion loss to Weld or HAZ in piping.
: Kind Regards Charlie
------------ End Original Message ------------

Try using Refracted Longitudinal search units.


 
 Reply 
 
Jim Knowles
Jim Knowles
00:12 Mar-28-2006
Re: UT Flaw detection in Monel and Hastelloy weldments
----------- Start Original Message -----------
: : Interested to know of any UT Techniques for Monel or Hastelloy weldments which would give a reasonable POD for preferential ID corrosion loss to Weld or HAZ in piping.
: : Kind Regards Charlie
: Try using Refracted Longitudinal search units.
------------ End Original Message ------------


The corrosion of this type can be put into three categories,notch, U type or escarpment, two can be detected relatively easily by a 45 degree shear either 0.5 skip or multiple skip paying attention to the particular area of impingement or beam path length. The escarpment type of geometry is more difficult as it is shallow from the pipe side gradually getting deeper nearer the weld or HAZ. Try using 4.0 MHz shear or if the material is partcularly noisy angled compression as Charlie recommends.



 
 Reply 
 
J. Mark Davis
Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama, USA, Joined Mar 2000, 85

J. Mark Davis

Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama,
USA,
Joined Mar 2000
85
04:21 Mar-28-2006
Re: UT Flaw detection in Monel and Hastelloy weldments
IS this just corrosion or is ID cracking a concern.

Refracted Longitudinal Waves may work and even ID Creeping Waves.

Phased Array UT is another consideration. Either a E Scan or a S-Scan could image the sorroded area.

Is there any weld crown restriction?

How thick is the Hastelloy and Monel material?

J. Mark Davis

----------- Start Original Message -----------
: : Interested to know of any UT Techniques for Monel or Hastelloy weldments which would give a reasonable POD for preferential ID corrosion loss to Weld or HAZ in piping.
: : Kind Regards Charlie
: Try using Refracted Longitudinal search units.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

GUL Subsea Solutions - Screeening & Monitoring

To inspect new and existing subsea lines, you need proven technology and experience. GUL offers it's
...
technology to solve this challenge: GUL Subsea and gMAT Transducer Rings.
>

Portable Ground Penetrating Radar - Proceq GP8000

The Proceq GP8000 portable ground penetrating radar instrument is the beginning of a new era in ND
...
T. The outstanding, patented ultra- wideband technology combined with a compact wireless probe delivers unmatched industry performance. Proceq GP8000 is the world’s first large-scale inspection solution that utilizes Augmented Reality in industrial applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window