where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
615 views
Technical Discussions
Ron Olson
R & D, Aviation
The Best Aviation Company In The World, USA, Joined Feb 2005, 23

Ron Olson

R & D, Aviation
The Best Aviation Company In The World,
USA,
Joined Feb 2005
23
00:02 Sep-23-2006
Tap Hammers

Besides those recommended by the FAA in AC43-13, can someone tell me where I can find some tap hammers?

Is there a vendor that sells tap hammers? For metal bonds? For composites?

I remember using a very dense (steel) one inch head and three inch lever arm with a yellow plastic handle. Who makes this?

Thank you.


    
 
 Reply 
 
Roberto Falconio
Engineering, NDT/Metrology SUPERVISOR
El Salvador, Joined Feb 2000, 13

Roberto Falconio

Engineering, NDT/Metrology SUPERVISOR
El Salvador,
Joined Feb 2000
13
05:36 Sep-24-2006
Re: Tap Hammers
Hi Ron,

Basically you may manufacture it according to aircraft manufacturer recomendations in case of a hand held mechanical tapping, however if you eould like an electronic equipment you may look for the woodpecker manufacturer by mitsui in Japan

Best Regards
RF

----------- Start Original Message -----------
: Besides those recommended by the FAA in AC43-13, can someone tell me where I can find some tap hammers?
: Is there a vendor that sells tap hammers? For metal bonds? For composites?
: I remember using a very dense (steel) one inch head and three inch lever arm with a yellow plastic handle. Who makes this?
: Thank you.
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window