where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
Mobile-Friendly Implementation in Progress

NDT.net Issue - 2018-01 - NEWS
2018-01 NDT.net Journal,

Sonotron NDT announces the new release of the ISONIC EXPERT FFC SW application: PA ultrasonic inspection and evaluation of Flange Face Corrosion


Sonotron NDT63, Rehovot [Israel]
 
NDT.net Journal
Issue: 2018-01
ISONIC EXPERT FFC software application was created for the detection and evaluation of flange face corrosion with use of wedged linear array probe situated either on the flange or taper surface; it may run in the ISONIC 3510, ISONIC 2010, and ISONIC 2009 UPA Scope instruments and featured with:

[+]

  • Built-In Flange Geometry Editor and Ray Tracer - Scanning Pattern (Scan Plan) Design
  • Intuitive Image Guided PA Pulser Receiver with Beam Forming View
  • True-To-Geometry Cross-Sectional Coverage and line scanning around the flange line either encoded or time based
  • "On-the-fly" True-To-Geometry Flange Overlay Volume Corrected Imaging:
    • Cross Sectional Slices
    • Top (C-Scan) View
    • Side View
    • End View
    • 3D View
  • DAC / TCG Data / Image Normalization
  • Independent on TCG Angle Gain Compensation / Gain Per Focal Law Correction
  • Automatic Coupling Monitor
  • 100% Raw Data Capturing
  • FMC/TFM Protocol for the data acquisition and imaging
  • Automatic Defects Alarming Upon C-Scan Acquisition Completed
  • Automatic Creation of Editable Defects List
  • Comprehensive Postrpocessing Toolkit Including:
    • Recovery and Evaluation of the Captured A-Scans from the Recorded Cross Sectional Views and C-Scans
    • Recovery of the Cross Sectional Views from the Recorded C-Scans
    • Converting Recorded C-Scans or their Segments into 3D Images
    • Off-Line Gain Manipulation
    • Off-Line DAC Normalization of the Recorded Images / DAC Evaluation
    • Numerous Filtering / Reject Options ( by Geometry / Position / By Amplitude db-toDAC / etc ) and Regeneration of the Corresponding of Editable Defects List and Storing it into a Separate FIle
    • Defects Sizing
    • Automatic creating of inspection reports - hard copy / PDF File
The video below illustrates the results obtained on the performance demonstration block (real flange with the artificial and real defects) with the use of ISONIC 3510 whilst running FFC inspection SW application:

Related links:

Sonotron NDT

More of Sonotron NDT published in NDT.net
2018-11-01: Toggling between S-Scan and FMC/TFM coverage whilst inspecting simple and complex geometry welds and other structural elements
2018-11-01: PAUT and Conventional Modality for the Materials Characterization using Frequency Domain Signal Presentation (FFT)
2018-10-01: Short Range Guided Wave Inspection – Annular Rings with Narrow Outer Chime
2018-09-01: MULTIGROUP T – the new inspection modality combining live S-Scan and FMC/TFM coverage out of the same PA Probe
2018-08-01: Complete PAUT Solution for the In-Service Inspection of Annular Ring Plates in the Above Ground Storage Tanks
2018-07-01: Sonotron NDT Brings the Annual Verification (Calibration) of PAUT Instruments to the Overnight Automatic Procedure at the Premises of the Instrument Owners
2018-06-01: PAUT: Rapid Detection and Evaluation of the Fatigue Cracks in the Web-to-Outboard End Pad Fillet Radius at Lower Wing Attach of an Aircraft
2018-05-01: Sonotron NDT introduces the upgraded version of ISONIC PA AUT platform
2018-05-01: Automatic finding, sizing, and alarming of the defects upon PAUT scanning completed
2018-04-01: Sonotron NDT expands the applications portfolio for PAUT of welds
All 63 Articles & News of Sonotron NDT in NDT.net

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window