where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

NDT.net Issue - 2019-05 - NEWS
2019-05 NDT.net Journal,

3 Tips for Accurate Small-Diameter Tubing Measurements


Olympus Scientific Solutions Americas (OSSA)221, Waltham, MA, USA
 
NDT.net Journal
Issue: 2019-05
Small-diameter metal and plastic tubing is used in a wide variety of industrial and medical applications. Some of these tubes can be smaller than 0.125 inches (3 mm) in diameter, with very thin walls. When their applications are safety-critical, they need to meet tight manufacturing tolerances for wall thickness and concentricity. In the past, manufacturers would have to cut the samples to visually inspect the tube or measure the wall thickness using calipers. Today, there’s a fast and nondestructive alternative for quality control inspections of small-diameter tubing, ultrasonic (UT) thickness gaging.

Accurate Small-Diameter Tubing Measurements

Recommended UT Thickness Gage, Equipment, and Inspection Setup

For tubing with a diameter of less than 0.125 in. (3 mm), we usually recommend using a 20 MHz focused immersion transducer. To efficiently transmit sound energy into a small-diameter part, it’s necessary to focus the sound into a narrow beam. Focused immersion transducers use a contoured acoustic lens along with a column of water to focus the sound beam for increased sensitivity. The RBS-1 bubbler is a desktop immersion-tank and probe fixture that creates a steady column of water and helps keep the test piece centered in the sound beam. To create a consistent, low-flow water column, the immersion tank must be used with one of the bubbler nozzles, which should be matched to the application. A B103 V-notch bubbler simplifies tubing concentricity checks, since it enables you to rotate the tubing to quickly measure the thickness around the entire circumference and slide the tubing over the probe to measure the thickness along the length of the part.

B103 V-notch bubbler with the RBS-1-15 recirculating bubbler system
B103 V-notch bubbler with the RBS-1-15 recirculating bubbler system

We recommend using an Olympus 38DL PLUS® or 45MG ultrasonic thickness gage (using the 45MG-SE single element and 45MG-WF waveform software options) along with a 20 MHz M316-SU immersion transducer with a 0.75 in. (19 mm) focus for this application.

Small-diameter tubing inspections can be easy when using the proper equipment and correctly calibrated instruments, but measurement errors may still occur. Here are 3 simple tips to help you avoid common issues.

1. Use the IF Blank function to avoid the interface echo trailing edge

When measuring steel tubing with an immersion setup, it’s important to account for the water-to-steel interface echo. The acoustic impedance of water and steel are sufficiently different that they create an impedance mismatch, which results in a large interface echo. Thin-walled tubing creates back wall echoes that are very close together. In most cases, the trailing edge of the interface echo interferes with the first returning back wall echo. To avoid this interference, use the IF Blank function, which conceals the trailing edge of the interface echo, and choose a pair of clean successive echoes that are further out in time and interference free.

The trailing edge of the large interface echo interfering with the first back wall echo
The trailing edge of the large interface echo interfering with the first back wall echo

The IF Blank setting can be adjusted to select the strongest pair of signals. Although the selected pair of signals changes as the IF Blank is adjusted, the time of flight between successive back wall echoes remains the same.

Varying IF Blank settings results in the same thickness measurementVarying IF Blank settings results in the same thickness measurement
Varying IF Blank settings results in the same thickness measurementVarying IF Blank settings results in the same thickness measurement

2. Watch for varying back wall signal amplitude when using a focused immersion transducer

Because the water path length in the B103 bubbler plus the metal wall thickness of the part is significantly shorter than the transducer’s focal length, the largest echo amplitude occurs around the third or fourth multiple of the back wall echo, where the focus occurs. This effect is common when measuring thin metal, and it should not affect accuracy if the measured echoes are clean and undistorted, as seen here. To take an accurate measurement, use the IF Blank function to select two successive, distinct back wall echoes.

3rd and 4th multiples are the highest amplitude due to the focal length
3rd and 4th multiples are the highest amplitude due to the focal length

3. Don’t set the M3 Blank out too far

To avoid a false measurement, decrease the M3 Blank value until the gage records a measurement using successive back wall echoes, correctly representing the part thickness.

Detection between the 3rd and 5th back wall echoes
Detection between the 3rd and 5th back wall echoes

With the proper techniques, measuring wall thickness of thin-walled tubing is fast and simple with the 38DL PLUS and 45 MG ultrasonic thickness gages. For information on other thickness gaging applications, check out the links below.

Detection between the 3rd and 4th back wall echoes
Detection between the 3rd and 4th back wall echoes

Related Content

Tags: ness Gage, Ultrasonic, Conventional Ultrasound

By Calvin Jory - April 23, 2019
Product Marketing Specialist, Ultrasonic Flaw Detectors

Olympus Scientific Solutions Americas (OSSA)

More of Olympus Scientific Solutions Americas (OSSA) published in NDT.net
2019-04-01: Case Study: Inspecting Boiler Tube Welds Using the COBRA Ultrasonic Phased Array Solution Instead of Radiography
2019-04-01: Touch Down: Eddy Current Wheel Probes Help Ensure a Safe Landing
2019-03-01: Olympus Launches New Industrial Research Chair at Quebec Engineering School
2019-03-01: Eddy Current Array for Aircraft Engine Component Inspection
2019-03-01: Coherent Adaptive Focusing Technology for the Inspection of Variable Geometry Composite Material
2019-02-01: The (Sono)pen Is Mightier: 3 Tips to Improve Your Measurements
2019-01-01: For Goodness Sake - Assuring the Quality of Toys with Thickness Gages
2018-12-01: Train Inspection That Goes Beyond the Standard
2018-11-01: The FlexoFORM™ Scanner Provides a Complete Ultrasonic Testing Solution for Corrosion Inspection of Pipe Elbows
2018-10-01: Bridge-ing the Gap to Safety
All 267 Articles & News of Olympus Scientific Solutions Americas (OSSA) in NDT.net

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window